穿條操作

Wearing operation

上料：將待穿條的鋁合金型材放置在穿條機的進料臺上，確保型材的槽口與膠條輸送方向一致。對于一些較長的型材，可能需要使用輔助支撐裝置來防止型材下垂或晃動。

Loading: Place the aluminum alloy profile to be threaded on the feeding platform of the threading machine, ensuring that the groove of the profile is consistent with the direction of the rubber strip conveyor. For some longer profiles, auxiliary support devices may be needed to prevent the profiles from sagging or shaking.

啟動設備：打開穿條機的電源開關，啟動設備。設備啟動后，膠條會自動從放置架上被牽引進入穿條機的送料機構。

Start the device: Turn on the power switch of the strip threading machine and start the device. After the device is started, the rubber strip will be automatically pulled from the placement rack into the feeding mechanism of the threading machine.

穿條過程：膠條在送料機構的推動下，沿著型材的槽口前進。在穿條過程中，要注意觀察膠條是否能夠順利地進入槽口，以及膠條的位置是否正確。如果發現膠條有偏移或卡頓現象，應及時停機調整。

Thread process: The rubber strip is pushed forward along the groove of the profile by the feeding mechanism. During the process of threading, it is important to observe whether the rubber strip can smoothly enter the groove and whether the position of the rubber strip is correct. If the rubber strip is found to be offset or stuck, it should be stopped and adjusted in a timely manner.

切割膠條：當膠條穿到型材的末端時，穿條機的切割裝置會按照預設的長度將膠條切斷。切割后的膠條應與型材的端部齊平，確保門窗安裝后的美觀度。

Cutting rubber strip: When the rubber strip reaches the end of the profile, the cutting device of the threading machine will cut the rubber strip according to the preset length. The cut rubber strip should be level with the end of the profile to ensure the aesthetic appearance of the doors and windows after installation.

下料：穿條完成后，將穿好膠條的型材從出料臺上取下，放置在指定的位置。然后，重復上述上料、穿條、切割和下料的操作，直到完成所有型材的穿條工作。

Cutting: After threading, remove the profile with the rubber strip from the discharge table and place it in the designated position. Then, repeat the above operations of loading, threading, cutting, and unloading until all profiles are threaded.

設備維護

Equipment maintenance

清潔設備：在穿條機使用完畢后，及時清理設備上的膠條碎屑、型材粉末等雜物。可以使用壓縮空氣或吸塵器進行清理，確保設備的各個部件干凈整潔。

Cleaning equipment: After using the strip threading machine, promptly clean up any debris such as rubber strip fragments and profile powder on the equipment. Compressed air or a vacuum cleaner can be used for cleaning to ensure that all components of the equipment are clean and tidy.

保養部件：定期對穿條機的傳動部件、刀具等進行保養和維護。例如，對齒輪、鏈條等傳動部件添加潤滑油，對刀具進行刃磨或更換，以保證設備的正常運行和穿條質量。

Maintenance parts: Regularly maintain and upkeep the transmission components, cutting tools, etc. of the threading machine. For example, adding lubricating oil to transmission components such as gears and chains, and grinding or replacing cutting tools to ensure the normal operation and threading quality of the equipment.

檢查電器系統：定期檢查穿條機的電器系統，包括電線、插頭、插座、控制器等，確保電器連接牢固，無漏電、短路等安全隱患。如發現電器元件有損壞或故障，應及時更換或維修。

Check the electrical system: Regularly inspect the electrical system of the strip threading machine, including wires, plugs, sockets, controllers, etc., to ensure that the electrical connections are firm and there are no safety hazards such as leakage or short circuits. If damage or malfunction is found in electrical components, they should be replaced or repaired in a timely manner.

本文由穿條機友情奉獻.更多有關的知識請點擊:http://www.tzjddl.cn我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

This article is dedicated to friendship For more information, please click: We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message